The first ZS postal match is up:
http://zombiesquad.theedge.net/phpbb2/viewtopic.php?p=90658#90658
For more info or to Register drop an e-mail to: postalmatch@zombiehunters.org
The Target we will use:
http://www.kylenet.com/ZSpostmatch/ZSTARGET.pdf
Silhouette free verson for those that have pickier ranges:
http://www.kylenet.com/ZSpostmatch/ZSTARGET2.pdf
Print on 8x10 paper.
Postal Match
Moderator: ZS Global Moderators
10 posts
• Page 1 of 1
Postal Match
by kyle » Tue Jul 26, 2005 12:01 am
Zombie Squad - "We can handle it from here. We've talked about this on the Internet."
-
kyle - ZS Board Member
- Posts: 15169
- Joined: Wed Mar 17, 2004 3:18 pm
- Location: St. Louis
by Einstein » Fri Jul 29, 2005 1:29 pm
I had sent an e-mail but do not know if it went through?
Is a .38 spcl o.k. ? It is smaller than a 9mm.
Is a .38 spcl o.k. ? It is smaller than a 9mm.
"Any intelligent fool can make things bigger, more complex, and more violent. It takes a touch of genius - and a lot of courage - to move in the opposite direction." A. Einstein
ZS Fleet #0015 & ZS Fleet #0016
ZS Fleet #0015 & ZS Fleet #0016
-
Einstein - * * * * *
- Posts: 1765
- Joined: Fri Jul 15, 2005 1:26 pm
- Location: Appalachian Mountains
by kyle » Fri Jul 29, 2005 1:39 pm
Einstein wrote:I had sent an e-mail but do not know if it went through?
Is a .38 spcl o.k. ? It is smaller than a 9mm.
it is?
9 millimeters = 0.354330709 inch
Bear_B has final word but I'm pretty sure it's OK. If you didn't get an e-mail response from him by now you might want to send him another to make sure it went through.
Actual sizes:
.38 cal = .357 inch or 9.067mm
9mm = .355 inch or 9.017mm
Zombie Squad - "We can handle it from here. We've talked about this on the Internet."
-
kyle - ZS Board Member
- Posts: 15169
- Joined: Wed Mar 17, 2004 3:18 pm
- Location: St. Louis
by Einstein » Fri Jul 29, 2005 2:00 pm
I have a most ridiculous question then... I was at the range w/ a friend and we were using my .38 and my 9mm. He had grabbed the 9mm and attempted to put it in the .38 to find it went in partially and got stuck.
I assumed the 9mm was larger because of this? I know the .38 is longer but i thought it was smaller diam.
I assumed the 9mm was larger because of this? I know the .38 is longer but i thought it was smaller diam.
"Any intelligent fool can make things bigger, more complex, and more violent. It takes a touch of genius - and a lot of courage - to move in the opposite direction." A. Einstein
ZS Fleet #0015 & ZS Fleet #0016
ZS Fleet #0015 & ZS Fleet #0016
-
Einstein - * * * * *
- Posts: 1765
- Joined: Fri Jul 15, 2005 1:26 pm
- Location: Appalachian Mountains
by kyle » Fri Jul 29, 2005 2:29 pm
Einstein wrote:I have a most ridiculous question then... I was at the range w/ a friend and we were using my .38 and my 9mm. He had grabbed the 9mm and attempted to put it in the .38 to find it went in partially and got stuck.
I assumed the 9mm was larger because of this? I know the .38 is longer but i thought it was smaller diam.
Shit, I don't know. I don't own a .357 or .38 so this is purely google experience. Next time I hit the range with Jamoni I'll steel one of his rounds and find out for sure.
Anyone ave a picture with the two side by side? This is discussion for another thread though.
Zombie Squad - "We can handle it from here. We've talked about this on the Internet."
-
kyle - ZS Board Member
- Posts: 15169
- Joined: Wed Mar 17, 2004 3:18 pm
- Location: St. Louis
-
zXzGrifterzXz - * * * * *
- Posts: 6785
- Joined: Sat Feb 12, 2005 8:17 pm
- Location: Mesa, AZ
by TheBlunderbuss » Tue Aug 02, 2005 12:56 am
I'm in the same boat -- gotta use .38 or .357. That IS my "service" revolver.
-
TheBlunderbuss - * * * * *
- Posts: 2613
- Joined: Sun Oct 03, 2004 12:38 pm
- Location: Blago ville
10 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 1 guest